Design Your Own Kpop Light Stick Game

Components and supplies

Apps and online services

About this project

The story

My daughter and her friends are huge fans of K-POP music and wanted to have one these fancy light sticks, that are common in the concerts of K-POP bands. Since those devices are sold for a very high price (my daughter, her friends and I) decided to build our own independend version. Just putting a blinking LED in a tube seemed too boring, so we made something more fancy.

Features

lot's of different multicolor light patterns to choose from

song specific presets, that change patters and color aligned with the music (verse, chorus, breaks...)

webinterface (also usable on smartphones browsers) for song selection, pattern programming and network configuration

BPM Detection and synchronization with integrated button

on the fly programming of any kind of song light shows

Saving and loading of complete light shows into internal flash memory

Connection features

Opens up its own WLAN Access Point in case connect to existing Networks can't be established or button is pressed at power on

Can connect to WLAN using previous known credentials or for credentials given through the web interface

Demo

Materials

Besides the electronic parts (delcared in the component section), you need some stuff to build the stick. Our blueprint was the "BTS Armybomb" and we chose the following materials:

30-40cm plastic pipe with 4cm diameter and a cap to close one end

10cm and 8cm plastic spheres

sandpaper

black acrylic color (not the best choice, since ist gets scratched off easy)

4 cm acrylic glass diamond

FIMO (a fast hardening dough) to create the cup for the optical unit

hot glue

Building the whole thing

Setting up the circuit was the easiest task. Building the software was the fun part and manufacturing the stick was try and error. So here are the main steps in a proper order:

The circuit

This should be no problem for anybody. One thing to note: For developing and testing all the light effects I used an Arduino Uno, since compiling and uploading is much faster. On the Arduino Uno the Button is connected to D5 and the Neopixel Data is connected to D12. These are also the numbers you find in the code. This confusion about coded pin and real pin is some weirdness of the ESP8266. So this schematic shows how to connect to the ESP8266 NodeMCU.

The software

There are 3 main sketches in the repository:

the_light_stick: The final firmware for the ESP8266 NodeMCU

LightShow_preparation: Reduced to the main show functions without any network and webui functionality. This can be run on an Arduino Uno. To change and test programms, check out the commands you can send over the serial interface

ui_preparation: Reduced to network and ui code so the resulting code is smaller and uploads faster to the NodeMCU. Also contains css and html file with the prototype, so layout development can be done by just editing these and provide it through a small webserver (e.g. miniweb)

One file is missing on purpose. You need to add wifi_credentials.h with #define STASSID and #define STAPSK.

If you just want to add or change the hard coded song presets, look into "SongPresets.ino" in "the_light_stick"

The optical unit:

create some sort of cup with FIMO or some other modelling material

inner diameter: a little bit smaller then the diamond

outer diameter: fits the inner diameter of the tube

inner depth is equal to the height of the diamond

a hole in the bottom for cables

solder cables to the neopixel jewel

glue neopixel Jewel to the bottom of the cup

glue diamond in the cup (and do that really strong, else it will shake loose and fly around)

The spheres

sand the 8cm plastic sphere evenly whith the sand paper.

cut out the holes in the spheres (We used small iron saw blades to first cut in some gaps and weaken the plastic where it should break. Afterwards we could break out the prepared sectors with a plier)

Assembly

drill hole in the tube for the button

connect all cables and route them as necessary throught the pipe

place Node MCU in the tube (Our version was sitting very tight in the diameter)

mount button in the hole

place and glue the optical unit

glue the speres

paint the stick in black

Manual

You find a whole manual (english and german) in the git project "docs" directory. This will also explain, how to programm song specific patterns by yourself with the web interface. To hardcode a pattern into the firmware just copy the programming strings you developed in the webinterface into the "SongPresets.ino" code.

Hardware Variation - D1 Mini

To use less space for the controller and have a more robust and modular setup, I created a variation, using a D1 Mini Board and a small PCB for easy montage.

Also we changed the material for the tube by reusing cardboard tubes from wrapping paper rolls. Here are some Pictures:

Code

Lightstick project on Github

Schematics

Circuit as Jpg

Circuit ue2vbtu2qi

Lightstick Circuit

Author

Published on

August 20, 2020

Members who respect this project

See similar projects
you might like